
Every few months someone posts a photo of a filament-printed space marine and the comments fill up with “is that resin?”. It is a fair question to take seriously now. A 0.2 mm hotend for a Bambu costs about a tenner, community profiles go down to 0.04 mm layers, and there is a whole catalogue of sculpts designed to print without supports. So has FDM caught up for miniatures, or is this still the one job where my resin printer roundup gives the right answer?
The short answer
Narrowed, not closed. FDM has caught resin on one measurement and stayed a long way behind on another, and which one matters depends on the size of the figure and how closely anyone will look at it.
Where FDM has caught up: layer height
Resin miniatures are usually printed at 30 to 50 micron layers. Two years ago FDM could not get near that. Now the FDMFoundry settings library and the r/FDMminiatures wiki list Bambu profiles for a 0.2 mm nozzle at 0.06 mm layers (Fat Dragon Games, ObscuraNox) and 0.04 mm (HOHansen’s version 2). That is 40 to 60 microns. On the vertical axis the two technologies are now in the same range, which is why a well-printed FDM cloak or shield can look so smooth in photos.
Where it has not: feature size
Layer height is only half of resolution. The other half is how small a feature the machine can draw in each layer, and here the physics has not moved. A 0.2 mm nozzle lays a line about 200 microns wide. Current hobby resin printers have pixels of 14 to 22 microns: 18 on the Elegoo Mars 5 Ultra, 14 by 19 on the Saturn 4 Ultra 16K, 22 on the Phrozen Sonic Mini 8K S. That is roughly a tenfold difference.
Here is what that means on a figure. My rough estimate is that the face of a 28 to 32 mm character is about 4 mm wide. An FDM printer gets about 20 lines across it. A resin printer at 18 microns gets about 220 pixels. Eyes, teeth, chainmail links and sword guards live in that difference, and no slicer profile changes the width of the hole in the nozzle. My nozzle size guide covers the general trade-off.

What people who have tried both actually say
I looked for writers who had printed the same sort of model both ways. They mostly agree, including the FDM enthusiasts.
- FauxHammer, a display painter, says a 0.2 mm nozzle on the A1 gives “passable results” and that resin is still the better route when tiny detail is the whole point.
- Micron Monster’s guide to FDM miniatures, written by a painter with 27 years in the hobby, calls the 0.2 mm nozzle essential and then lists what still fails: faces at 28 mm and below, fine cloth folds, filigree and chains. Its own summary is that the technique narrows the gap without removing it.
- 3DPrinting.com says a 28 mm figure with a face shows layer lines under primer whatever nozzle you fit, and that FDM works from about 40 mm upward on stylised sculpts. That page carries affiliate links and does not describe its own bench testing.
- Resin and Rolls, whose author runs an Elegoo Saturn beside a Neptune, tells readers to buy resin if minis are the goal and keep FDM for terrain. Also an affiliate site.
- On the other side, a blogger at nessy.info fitted a 0.2 mm hotend to an X1 Carbon in February, printed and painted an ork in a day, and was delighted. He owns a resin printer he has not touched in two years because of the mess and fumes.
That last one matters. Nobody in this list says FDM detail matches resin. Several say FDM is good enough that they stopped putting up with resin.
What has really changed for FDM
Three things, and only one of them is hardware.
The first is the cheap fine nozzle on a reliable printer. Bambu sells a 0.2 mm stainless hotend for the A1 series that swaps in minutes. The second is shared profiles: the ones named above are tested, versioned and free. The third is the models. Designers such as Brite Minis and Arbiter Miniatures sculpt for filament, with thicker weapons, fewer overhangs and no supports needed, and FDMFoundry’s catalogue listed 2,447 FDM-suited models when I looked. A sculpt made for the process hides most of what the process cannot do.
FDM also does one thing resin cannot: colour. With an AMS you can print a board-game piece in four colours and skip the painting.
The FDM costs nobody puts in the photo caption
Time is the big one. Bambu’s own 0.2 mm nozzle FAQ gives 2 mm³/s as the usual flow limit, a fraction of what a 0.4 mm nozzle manages. One support-free 32 mm sci-fi gunner on Printables is listed at 2 hours 40 minutes for 5 g of filament. A Bambu forum user printing a resin-supported figure on an A1 mini in July reported about 15 hours for the first attempt. Resin cures a whole layer at once, so a full plate of figures takes about as long as one.
Reliability at the limit is the other. That same forum thread is worth reading as a caution. Over four days the poster went from pleased to “really lost”: stringing, supports that would not come off cleanly, a support tree that detached mid-print. An experienced user replied that the popular fine profiles push the printer to its limits and need dry filament, a smooth plate, a draught-free room and a clean nozzle. Another said flatly that models pre-supported for resin print badly on FDM. My support settings guide is the place to start if you go this way.
Two smaller ones from Bambu’s FAQ: prints from a 0.2 mm nozzle are weaker than from a 0.4, and the stainless nozzle cannot take carbon-fibre, glow or sparkle filaments.
The resin costs: workflow and air

Resin’s detail comes with a process FDM does not have. Uncured resin is a skin irritant and sensitiser, so it is gloves on from the bottle to the cure. Prints are washed, then cured under UV, and the waste has to be cured before disposal, not rinsed down a sink.
On fumes there is new evidence this year. A study in ACS Chemical Health and Safety, published in January by researchers at Birmingham and Leicester, measured emissions from a Formlabs Form 2 with four resins. In a sealed chamber, total VOCs passed 128,000 µg/m³, which the authors treat as the worst case. In a ventilated room at 50 cm the figure was 45 to 116 µg/m³ and it fell back to baseline within two hours of the print ending. Standing 2 m away instead of 0.5 m cut exposure by 71 to 84%, and an extraction hood with carbon and HEPA filters helped too. Individual compounds stayed well below workplace limits, but the authors point out that many of them have no published limit at all, so long-term effects are unknown.
I read that as: fine in a ventilated room you are not sitting in, not fine in a closed cupboard or a bedroom. The study used a Formlabs machine and its resins, so it is a guide for hobby MSLA printers, not a measurement of them. GamesRadar’s five-star review of the Saturn 4 Ultra 16K, on a unit Elegoo supplied, praised detail the reviewer said could pass for commercial hard plastic, and its one complaint was that the printer has no air filtration built in. My fumes and ventilation guide covers the FDM side.
What each route costs
| Route | What you buy | UK price today |
|---|---|---|
| Already own a Bambu | 0.2 mm hotend | About £10 (€10.99 on Bambu’s EU store; I did not check the UK price) |
| FDM from scratch | A1 mini at £139 in Bambu’s sale to 1 December, plus the hotend | About £150 |
| Resin from scratch | Elegoo Mars 5 Ultra at £199 in Elegoo’s Black Friday sale, Mercury Plus V2.0 wash and cure station at £59, 1 kg of ABS-like resin at £16.99 | £274.99, plus gloves, IPA and somewhere ventilated to put it |
| Resin, bigger plate | Saturn 4 Ultra 16K at £359 in the same sale, same station and resin | £434.99 |

The totals are my arithmetic. Running costs are small either way. Resin and Rolls puts resin at $0.30 to $0.60 a figure. For FDM, a 5 g figure in Bambu PLA Basic at $17.99 a kilo is about 9 cents by my sum. Neither will be what decides it. See the Black Friday roundup for the Bambu prices.
So which should you use?
| If you are printing… | I would use | Why |
|---|---|---|
| 28 to 32 mm characters with faces | Resin | The detail is below what a 0.2 mm nozzle can draw |
| Display pieces you will paint to a high standard | Resin | Layer lines show under primer on FDM |
| Figures of 40 mm and up, monsters, stylised sculpts | Either | A fine nozzle holds up at this size |
| Rank-and-file for the gaming table | Either | They are seen at arm’s length; pick FDM-friendly sculpts |
| Terrain, scatter, vehicles and bases | FDM | Bigger bed, tougher parts, cheaper material |
| Multicolour board-game pieces | FDM | Colour straight off the printer |
| Anything, in a home with no ventilated spare space | FDM | No uncured resin to handle or store |

My own position, as someone with two filament printers and no resin machine: I would fit the 0.2 mm hotend and try FDM-friendly sculpts before buying anything else, because it costs a tenner to find out whether the results are good enough for my table. If I were painting single characters for display, I would not expect that to satisfy me, and the £275 resin setup would be the right spend, provided I had a ventilated place for it. Most people who are serious about miniatures seem to end up with both, resin for the heroes and FDM for everything they stand on. For painting what comes off either machine, my painting guide applies.
Where the evidence is thin
- I found no controlled test that printed the same sculpt on a current 16K resin printer and a tuned 0.2 mm FDM setup and measured the result. The comparisons are judgement by eye.
- Community FDM results are shown at their best. Failed prints do not get posted, and the forum thread above suggests they are common.
- The emissions study covers one Formlabs printer. I read its abstract and findings summary, not the full paper, and I found no equivalent study of a hobby MSLA printer.
- The 4 mm face width is my estimate, so treat “20 lines against 220 pixels” as an illustration.
- Print times vary hugely with sculpt, supports and profile. The two FDM figures I quote are single examples.
Sources and further reading
- FDMFoundry: print settings library
- Micron Monster: how to print miniatures on an FDM printer
- FauxHammer: Bambu A2L review
- 3DPrinting.com: best 3D printers for miniatures 2026
- Resin and Rolls: resin vs FDM for miniatures
- nessy.info: high-detail miniatures on FDM with a 0.2 mm nozzle
- Bambu Lab forum: Resin2FDM on an A1 mini with a 0.2 mm nozzle
- Bambu Lab wiki: 0.2 mm nozzle FAQ
- Printables: support-free 32 mm gunner (print time and weight)
- University of Birmingham: VOC emissions from a resin 3D printer (ACS Chemical Health and Safety, 2026)
- GamesRadar: Elegoo Saturn 4 Ultra 16K review
- Elegoo UK: Mars 5 series prices
- Elegoo UK: Mercury Plus V2.0
- Bambu Lab UK: Black Friday sale terms



